GuitarPCB | Barry | Activity https://guitarpcb.com/members/barry/activity/ Activity feed for Barry. Wed, 22 Jul 2026 03:07:52 -0400 https://buddypress.org/?v= en-US 30 hourly 2 c4f0bca37013bfbb6c0bb10f2483444b Barry replied to the topic Slice in PCB in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/slice-in-pcb/page/2/#post-39465 Sat, 18 Jul 2026 17:07:22 -0400 In the meantime I would take some time and carefully clean up the bottom 6-pin connector pads on the reverb side of the board.
I’d use a good Soldapullt-style solder sucker first, then follow up with some copper desoldering braid to remove as much solder from the holes as possible. Just be careful not to apply too much heat or linger too long, as…Read more

]]> 0 8875ffee703855409170a835fe9a8001 Barry replied to the topic Slice in PCB in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/slice-in-pcb/#post-39456 Fri, 17 Jul 2026 00:57:31 -0400

Also I was going to say that you need to make sure you have a power supply providing at least 100mA of current or it won’t work.

]]> 0 ab3f3ea5849df7eb547cddaca563d7cf Barry replied to the topic Slice in PCB in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/slice-in-pcb/#post-39452 Thu, 16 Jul 2026 18:08:14 -0400 At a glance I cannot make out IC6 well enough to confirm the correct orientation. The other thing I would check is that all voltage regulators are firmly seated since sockets can create intermittent contact. You can make a few minor back and forth bends in the leads to assure they are secure in the sockets. Also tell us what brand of L78L05 that…Read more

]]> 0 9df438adfb9f3ed36cd15e1bec498293 Barry replied to the topic Slice in PCB in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/slice-in-pcb/#post-39450 Thu, 16 Jul 2026 16:12:30 -0400 Yes, I am aware of what you are talking about. I was just pointing out that your scratch is very unlikely the problem.

]]> 0 78f0a2ee708e8014ecc2ccc1c0fe4265 Barry replied to the topic Slice in PCB in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/slice-in-pcb/#post-39447 Thu, 16 Jul 2026 03:43:48 -0400 The white line at the top is just a decorative silkscreen border.

]]> 0 8e0bd36543e0338f88e0494cfe171c61 Barry replied to the topic Gypsy Fuzz! in the forum Show Off Your Build https://guitarpcb.com/community/topic/gypsy-fuzz/#post-39441 Sun, 12 Jul 2026 21:34:38 -0400 Very nice! Thanks for sharing.

]]> 0 51e3840cbe1262547403bd6abdeae9f1 Barry replied to the topic Nostalgitone pcb plates in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/nostalgitone-pcb-plates/#post-39428 Fri, 10 Jul 2026 16:50:17 -0400 I have not personally tested any clear coats on the panels, so I can’t recommend one over the other.
I would suggest testing on a small area first, as acetone can potentially affect the printed silkscreen ink or finish.
I would like to hear your results though.

]]> 0 a277273e401c42697ec0c070a0cb8624 Barry replied to the topic Whats New with NostalgiTone: Message from Barry in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/whats-new-with-nostalgitone-message-from-barry/#post-39413 Tue, 07 Jul 2026 23:26:20 -0400 I wanted to give you a behind-the-scenes look at something I’m especially excited about. This is FrontStage, a new NostalgiTone project currently taking shape. While it’s designed to stand on its own, the real magic happens when it’s paired with DumbleTone in a future Dual Combo. With onboard order switching, you’ll be able to place either stage…Read more

]]> 0 d2fef15c8297fc0d0cc6097494d03db4 Barry replied to the topic Dooooooom! in the forum Show Off Your Build https://guitarpcb.com/community/topic/dooooooom/#post-39408 Sat, 04 Jul 2026 20:00:17 -0400 Very Nice Indeed! This is a fantastic sounding Distortion.

Thanks for sharing.

]]> 0 70c8d78a1816f332c165f26bfa552264 Barry replied to the topic NostalgiTone Rock Hard Finished!! in the forum Show Off Your Build https://guitarpcb.com/community/topic/nastalgitone-rock-hard-finished/#post-39403 Fri, 03 Jul 2026 19:27:52 -0400 That turned out fantastic! Thanks for sharing the build and the great feedback.

I’m really glad to hear everything went together so smoothly. Enjoy the ROCK⚡HARD!

]]> 0 f8511f564f9fc63def717a3752083c3d Barry started the topic Whats New with NostalgiTone: Message from Barry in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/whats-new-with-nostalgitone-message-from-barry/ Tue, 30 Jun 2026 21:23:08 -0400 I’ve been spending a lot of time behind the scenes over the past few months designing and testing a whole new lineup of NostalgiTone projects. I’m excited to finally share a preview of what’s been keeping me busy.

These are just some of the projects currently in development. Several are already complete, others are in final testing, and I still…Read more

]]> 0 9f63f1b76bc4123a3afd28fa50e2faa0 Barry replied to the topic Plexamp single goes to 11! in the forum Show Off Your Build https://guitarpcb.com/community/topic/plexamp-single-goes-to-11/#post-39382 Fri, 26 Jun 2026 23:28:16 -0400 Thanks Steve.

And another I just finished today.

I hope that helps with the request of “keep em coming” from OP jmgrabowski

]]> 0 dbf70166d5b94f91c64fa80729966d52 Barry replied to the topic Plexamp single goes to 11! in the forum Show Off Your Build https://guitarpcb.com/community/topic/plexamp-single-goes-to-11/#post-39380 Fri, 26 Jun 2026 17:22:57 -0400 Looks great and thanks for posting!

The PLexAmp is such a great piece in the NostalgiTone line that fills the need for any situation requiring a Marshall Plexi tone.

Here are just a few notable examples over the decades.

 

A perfect fit for the NostalgiTone line.

as for “keep them coming” here are just a couple of the many I am working…Read more

]]> 0 e092ba25fbbc68e941f32a09da8cfa2b Barry replied to the topic NostalgiTone PCB Plates - New Catalog in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/nostalgitone-pcb-plates-includes-feedback-poll/#post-39292 Wed, 17 Jun 2026 23:59:18 -0400 These new Plates will be available soon.

 

 

 

 

 

 

 

 

 

 

 

 

]]> 0 1c64e49fb52d4b881807a29dde7ad2aa Barry replied to the topic Completed Builds. Some with Skins. Others with UV print and Labels. in the forum Show Off Your Build https://guitarpcb.com/community/topic/completed-builds-some-with-skins-others-with-uv-print-and-labels/#post-39251 Thu, 11 Jun 2026 02:54:32 -0400 Very nice, and thanks for sharing!

I’d be interested to hear more about some of the tones available, particularly when the combo builds are used in tandem with the order switching. It would be great to hear which combinations have become your favorites.

]]> 0 ca1d4fdc08e294bb9ce3a72ceebb6b60 Barry replied to the topic Best Ever OD in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/best-ever-od/#post-39249 Thu, 11 Jun 2026 00:37:01 -0400 I agree! That said, D7 and D8 are easier to switch.

]]> 0 74c80f195c88f45103a636a12cef575a Barry replied to the topic Best Ever OD in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/best-ever-od/#post-39247 Thu, 11 Jun 2026 00:02:06 -0400 <p class=”isSelectedEnd”>Yah, I obviously had a brain cramp while trying to answer too quickly. :oops:</p>
D7 and D8 are the hard clipping diodes in this circuit. Also much easier to mod.

]]> 0 97eaeafe2744a8b1a483561e2e6ce306 Barry replied to the topic NostalgiTone Naga Boost with new face plate Finished! in the forum Show Off Your Build https://guitarpcb.com/community/topic/nastaligitone-naga-boost-with-new-face-plate-finished/#post-39238 Tue, 09 Jun 2026 20:34:53 -0400 Very Nice and thanks for sharing.

]]> 0 cb46c888ac91e978bba1c19bde0aa5bf Barry replied to the topic Best Ever OD in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/best-ever-od/#post-39237 Tue, 09 Jun 2026 20:01:39 -0400 D3 through D6.
I really have no specific suggestions other than perhaps trying LEDs, but clipping is very subjective. Experiment and have fun.

]]> 0 68c0028b37381822710bf29212f2cbc4 Barry replied to the topic The GUIDES PAGE - Mandatory Reading for all! in the forum Forum Rules https://guitarpcb.com/community/topic/pedal-building-guides-mandatory-reading/#post-39208 Sat, 06 Jun 2026 01:19:59 -0400 Do not post here or after this line!

———————————————————————–

]]> 0 c6a061282dff34acd7b3a8ca8ebc6e28 Barry replied to the topic The GUIDES PAGE - Mandatory Reading for all! in the forum Forum Rules https://guitarpcb.com/community/topic/pedal-building-guides-mandatory-reading/#post-39207 Sat, 06 Jun 2026 01:18:06 -0400 ElectroSmash is down so I am putting this here in case.

This is a list of PDF file links and not a complete backup. For that you need to try Archive.org

 

 
Electrosmash.com Articles
This is a PDF backup of the most popular articles from Electrosmash.com, which has been experiencing hosting problems and has been unavailable.

It is NOT a…Read more

]]> 0 4753ee8b8bc57b4f8c05ed6354cdd84a Barry replied to the topic NostalgiTone PCB Plates - New Catalog in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/nostalgitone-pcb-plates-includes-feedback-poll/#post-39205 Thu, 04 Jun 2026 20:48:57 -0400 Thanks Jay. I agree 100%. That is definitely in the works.

]]> 0 58b0abf133bc985297157c2ee7d9c23d Barry started the topic NostalgiTone PCB Plates - New Catalog in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/nostalgitone-pcb-plates-includes-feedback-poll/ Thu, 04 Jun 2026 19:15:57 -0400

 
The initial response to the new NostalgiTone PCB Plates has been very encouraging, and I have been steadily expanding the lineup with new Singles, Dual Combos, and Triple Combo designs.
You can view the current catalog here:
[NostalgiTone PCB Plate Catalog]
Please note that some of the designs shown in the catalog are still under development…Read more

]]> 0 ba63152994f7051aeb11432b793f2564 Barry replied to the topic 60’s fuzz and 70’s brit in the forum Show Off Your Build https://guitarpcb.com/community/topic/60s-fuzz-and-70s-brit/#post-39187 Sat, 30 May 2026 17:31:43 -0400 Those look fantastic and thanks for sharing.

The trim pot is a necessity for the Fuzz. You could even mount it as a pot for a quick change. I also like how the Bass pot can be used to adjust your tone between say a Strat and Les Paul guitar switch. I roll off Bass for the Les Paul and add some for the Strat.

]]> 0 c49ecd23dbecace11c216c8b4726ba5f Barry replied to the topic Marsha Tone PCB High Freq Noise (solved) in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/marsha-tone-pcb-with-high-frequency-noise/#post-39178 Wed, 27 May 2026 16:14:44 -0400 Here is a Marsha Tone finished build thread which may be helpful for comparison.

Heavy Metal Thunder – High Gain combo build feat. Marsha

]]> 0 66d901c2b91b5c4c10cccb10c4061be4 Barry replied to the topic Marsha Tone PCB High Freq Noise (solved) in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/marsha-tone-pcb-with-high-frequency-noise/#post-39177 Wed, 27 May 2026 16:05:52 -0400 The 4V readings throughout parts of the audio path are normal for this type of op amp circuit and do not indicate a short between power and audio.

Also, adding a cap across R14 would largely duplicate the filtering/stabilization already happening in the VB network via C12, which is standard. You are certainly welcome to try it since it is an easy…Read more

]]> 0 c18149bdab1b11b0d598ad7959bb8bb0 Barry replied to the topic Space Modulator chorus (solved) in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/space-modulator-chorus/#post-39148 Thu, 21 May 2026 18:21:22 -0400 Re-flow solder joints.

]]> 0 fdf45b51c865de05972eb76ff66ce244 Barry replied to the topic SWAH diode. D3 in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/swah-diode-d3/#post-39147 Thu, 21 May 2026 18:19:50 -0400 I left you this message when you wrote that your Angry Llama was working.

]]> 0 39fc17e47fdbe198e0ed441fc3b06537 Barry replied to the topic Angry llama squeal issue (solved) in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/angry-llama-squeal-issue/#post-39127 Sun, 17 May 2026 15:49:44 -0400 I am glad you got it sorted out. Thanks for reporting back.
A quick tip when building pedals is to remember that the pedal itself is only one part of the overall signal chain. Things like pickup output, guitar type, amp settings, and even playing style can all have a significant effect on how a circuit responds.
With regard to the SWAH, this is…Read more

]]> 0 d5a88d704b0fdc6e82becff0e553f2ed Barry replied to the topic Angry llama squeal issue (solved) in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/angry-llama-squeal-issue/#post-39122 Sat, 16 May 2026 15:00:43 -0400 Also, just flip the switch and tell me if it goes away.

]]> 0 6b0681ba8b95c5a74b0e0c3b372da195 Barry replied to the topic Angry llama squeal issue (solved) in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/angry-llama-squeal-issue/#post-39121 Sat, 16 May 2026 14:44:44 -0400 The value prevents noise. Does not affect tone. Do not use tantalum.

]]> 0 3d61f89de3c47962d3520e5538b01464 Barry replied to the topic Angry llama squeal issue (solved) in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/angry-llama-squeal-issue/#post-39119 Sat, 16 May 2026 14:31:05 -0400 Make sure the Boost in the middle is not cranked. Not my circuit but it is called Angry for a reason.

If that doesn’t help and you have spare components you could try changing C4 from 100p up to 330p or 470p

]]> 0 1ce7d8da2059ed569c9ee13001ea377f Barry replied to the topic Finally finished .... and it actually works!! in the forum Show Off Your Build https://guitarpcb.com/community/topic/finally-finished-and-it-actually-works/#post-39094 Mon, 11 May 2026 18:54:11 -0400 Congrats on getting it up and running! That is definitely a more ambitious choice of circuits for an early build. The standing resistors look great too.
Most important thing is that it works and now you have a solid foundation moving forward from here.

Here’s a helpful tip for soldering jacks: apply a small amount of liquid flux to the jack l…Read more

]]> 0 9d6f807111f1b3b8d5087cdb9cc54bf0 Barry replied to the topic GuitarPCB 17th Anniversary – New Merch! in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/guitarpcb-17th-anniversary-25-off-new-merch/#post-39093 Mon, 11 May 2026 18:42:09 -0400 Thanks guys!

In some ways, 17 years seems like a very long time. In others, it really doesn’t. I guess it depends on the day.

We’ve lost a few shining stars along the way, and I still think about them all the time.

The business was originally started so I could work from home and raise my kids. That mission was accomplished, and now the nex…Read more

]]> 0 bdb2e097358b9acfe3bba5bceced361e Barry started the topic GuitarPCB 17th Anniversary – New Merch! in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/guitarpcb-17th-anniversary-25-off-new-merch/ Mon, 04 May 2026 03:36:37 -0400 Hi everyone,
I’m celebrating 17 years of GuitarPCB, and I just want to say thanks to all of you who have supported the site, shared builds, and been part of the community over the years.
To mark the occasion, I’m running my biggest sale of the year:
👉 25% OFF EVERYTHING in the shopUse code: SAVE25
This includes:

  • NostalgiTone combos

    • Read more

    ]]> 0 cee5a82a2fd48912ae23a38bb64f91a8 Barry replied to the topic 60’s triple combo pedal kill switches in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/60s-triple-combo-pedal-kill-switches/#post-38987 Fri, 01 May 2026 23:31:13 -0400 Never happened to me.

    The only thing I can think of is a short, or perhaps the Green blew out leaving the Red only.

    I would check for a solder bridge, and also probably just replace the LED with a pre-tested one using a 3v coin battery. Must be common anode.

    ]]>     0     894a8349462f23995cb8b260a770f85b Barry replied to the topic Doom Prophet LED in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/doom-prophet-led/#post-38985 Fri, 01 May 2026 16:48:23 -0400 Depending on the value of the CLR that was used you may have instantly blown the previous LEDs.

    I would try another new LED. You can pre-test with a 3v coin battery.

    If that doesn’t help I would test the connections between the 3PDT and main board with regard to the LED usiing your DMM in continuity mode.

    ]]>     0     8f0e3fed23e6e3d1d1c967fc992c47d8 Barry replied to the topic Doom Prophet LED in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/doom-prophet-led/#post-38983 Thu, 30 Apr 2026 03:36:03 -0400 What value of current limiting resistor are you using on the 3PDT?

    It’s too hard to see but looks different.

    ]]>     0     824ee86154dc59154af5604b957a0786 Barry replied to the topic NostalgiTone NT Phaser V1 in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/nostalgitone-nt-phaser-v1/#post-38981 Wed, 29 Apr 2026 17:30:56 -0400 The LDR itself is very simple and has no polarity, so orientation doesn’t matter. If it did, it would be clearly noted in the build document and indicated on the PCB silkscreen.
    If you check the schematic in the build document, you’ll see how the LDR ties into the phase-shifting stage, which is the core of the circuit. Each stage shifts the pha…Read more

    ]]>     0     d93eea5aba6507b415b5e14b4e19a07d Barry replied to the topic Band of Gypsys finished with GPCB aluminum face plate! in the forum Show Off Your Build https://guitarpcb.com/community/topic/band-of-gypsys-finished-with-gpcb-aluminum-face-plate/#post-38979 Wed, 29 Apr 2026 01:28:32 -0400 Yes, that’s what I mean and thanks for posting.

    A picture is sometimes worth a thousand words.

    ]]>     0     69dbba050d372bf97a180025791a9fa2 Barry replied to the topic Band of Gypsys finished with GPCB aluminum face plate! in the forum Show Off Your Build https://guitarpcb.com/community/topic/band-of-gypsys-finished-with-gpcb-aluminum-face-plate/#post-38977 Wed, 29 Apr 2026 00:43:48 -0400 Great build—looks awesome, and thanks for posting it.
    I don’t think people always realize how small these are compared to a 1590DD. That’s a ton of pedal crammed into a really tight space.

    ]]>     0     b491eae1b3b72d2e8ab53bc9104388c1 Barry replied to the topic NostalgiTone NT Phaser V1 in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/nostalgitone-nt-phaser-v1/#post-38974 Tue, 28 Apr 2026 19:48:47 -0400 It is perfectly fine to solder IC Chips to the PCB if you are good at doing it without over heating them. I do it all the time. I did say above in my post that the first things to solder are the Diode and Sockets.

    Anyway I would just go ahead and build it up but take your time and carefully plot your course.

    ]]>     0     53c19bd49168dc223fb6d025c14aa59b Barry replied to the topic NostalgiTone NT Phaser V1 in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/nostalgitone-nt-phaser-v1/#post-38961 Sun, 26 Apr 2026 16:16:38 -0400 Also the Phaser is one of a few PCBs that use standing resistors unless you have 1/8 resistors. It is the only way to fit everything on the PCB. So if you have the standard 1/4 resistors you need to do the standing resistor technique.

    As pointed out above start with low lying components first but keep in mind standing resistors are about as tall…Read more

    ]]>     0     ba0a8ab10288c9473031c68fdbdfabd0 Barry replied to the topic NostalgiTone NT Phaser V1 in the forum GuitarPCB Build Support https://guitarpcb.com/community/topic/nostalgitone-nt-phaser-v1/#post-38953 Sat, 25 Apr 2026 21:45:01 -0400 Hi and welcome.

    There are several beginner guides on the Guides Page.

    You can access through the Main Menu Bar up top or:

    The GUIDES PAGE – Mandatory Reading for all!

    Scroll down and find the tings you need and take your time.

    ]]>     0     46c4c0a05de4c0162a5c9462257738a4 Barry replied to the topic Finished!! Bonus PC EXH Lizard Queen! in the forum Show Off Your Build https://guitarpcb.com/community/topic/finished-bonus-pc-exh-lizard-queen/#post-38946 Fri, 24 Apr 2026 01:39:25 -0400 Ahh, very nice indeed.

    ]]>     0     22f9e4e7587b353e376a03a06ff3fbd8 Barry replied to the topic NostalgiTone Panel Contest in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/nostalgitone-panel-contest/?view=all#post-38932 Tue, 21 Apr 2026 02:20:34 -0400 The results are in for the NostalgiTone Panel Contest — thanks to everyone who took the time to enter.

    I ended up combining five sets of rankings to arrive at the final placements, based on the criteria outlined (overall presentation, build execution, and panel integration).

    Final Results

    🥇 1st Place — Zoso / 2112 (jmgrabowski)
    This one sto…Read more

    ]]>     0     494834f540fe9980c7cc208ac03f7e8e Barry replied to the topic NostalgiTone Panel Contest in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/nostalgitone-panel-contest/#post-38929 Sat, 18 Apr 2026 16:12:19 -0400 These all look fantastic — thank you to everyone who submitted an entry.
    I’m going to take a day or two to review everything and gather a few additional opinions so I can put together a fair overall ranking. I’ll post the results shortly after that.

    ]]>     0     1e8316020d1eefdd00e8e7d6472d9337 Barry replied to the topic NT Harbinger Fuzz single. in the forum Show Off Your Build https://guitarpcb.com/community/topic/nt-harbinger-fuzz-single/#post-38928 Sat, 18 Apr 2026 16:11:53 -0400 Very nice Harbinger!

    ]]>     0     8e9c5bcc2f36822704900104fc20d8e5 Barry replied to the topic NostalgiTone Panel Contest in the forum General DIY Pedal Discussion https://guitarpcb.com/community/topic/nostalgitone-panel-contest/#post-38920 Fri, 17 Apr 2026 15:33:22 -0400

    This is a re-posted submission from Matt

    ]]>     0     cfca7c044f62546ef63804dacbad26aa Barry replied to the topic Wylde Child… in the forum Show Off Your Build https://guitarpcb.com/community/topic/wylde-child-2/#post-38905 Sat, 11 Apr 2026 16:22:29 -0400 Congrats!

    The trimmer is for setting the bias of the chorus. There will be a fine spot where you will hear the best chorus. Sounds like you found it. I will update the build document.

    Is this going to be a contest entry?

    ]]>     0